Difference between revisions of "IGT:ToolKit/Build-OpenIGTLink"

From NAMIC Wiki
Jump to: navigation, search
 
(15 intermediate revisions by 2 users not shown)
Line 1: Line 1:
 
Back to [[IGT:ToolKit|IGT:ToolKit]]
 
Back to [[IGT:ToolKit|IGT:ToolKit]]
  
−
You are assumed that Slicer 3 has been built on your computer.
+
=Notes before you begin=
 +
* Slicer3 is assumed to have been built on your computer in the directory '''igt-tutorial'''.  This means that you have the directories igt-tutorial/Slicer3, igt-tutorial/Slicer3-build and '''igt-tutorial'''/Slicer3-lib
 +
* CMake 2.6 is absolutely required.  If you don't have it installed, you can use the version of ccmake found in '''igt-tutorial'''/Slicer3-lib/CMake-build/bin (it will be CMake 2.6)
  
−
1. In directory '''igt-tutorial''', download OpenIGTLink module source code:
+
=Instructions=
−
    svn co http://www.na-mic.org/svn/NAMICSandBox/trunk/IGTLoadableModules
 
−
2. In directory '''igt-tutorial/IGTLoadableModules''', create a new directory '''OpenIGTLink-build'''
 
  
−
3. Cd to '''OpenIGTLink-build''', and run the following command to configure the project:
+
First, get the OpenIGTLink module source code from the repository:
−
  ccmake ../OpenIGTLink
+
  $ cd '''igt-tutorial'''
−
You need to set '''Slicer3_DIR''' as the build directory of Slicer3, i.e. Slicer3-buld. Also, make sure you have version 2.6 of CMake installed. If you don't, you can find in Slicer3-lib/CMake-build/bin. After configuration, run
+
  $ svn co http://svn.na-mic.org/NAMICSandBox/trunk/IGTLoadableModules/OpenIGTLink OpenIGTLink
−
make  
+
 
−
To build OpenIGTLink. Upon completion, you should find '''libOpenIGTLink.so''' here at igt-tutorial/OpenIGTLink-build/lib/Slicer3/Modules
+
Create a new build directory:
 +
  $ mkdir OpenIGTLink-build
 +
 
 +
Configure using CMake 2.6:
 +
* Run CMake - CMake is found in '''igt-tutorial'''/Slicer3-lib/CMake-build/bin 
 +
* Set the source code directory to '''igt-tutorial'''/OpenIGTLink
 +
* Set the build directory to '''igt-tutorial'''/OpenIGTLink-build
 +
* Press the 'c' key (or the configure button) - this give you a dialog box telling you that you haven't set the Slicer build directory yet
 +
* Set '''Slicer3_DIR''' to your build directory of Slicer3 (i.e. Slicer3-build)
 +
* Press 'c' (or the configure button) again
 +
* Then press the 'g' key (or the OK button) to generate the Visual Studio solution (Windows) or makefiles (linux)
 +
 
 +
=== Windows ===
 +
* Open OpenIGTLink.sln in the OpenIGTLink-build folder
 +
* Build -> Build Solution
 +
 
 +
Upon completion, you will find '''OpenIGTLink.dll''' in OpenIGTLink-build/Debug
 +
 
 +
Copy OpenIGTLink.dll into '''igt-tutorial'''/Slicer3-build/lib/Slicer3/Modules/Debug
 +
 
 +
=== Linux / Mac OS X ===
 +
* ccmake is found in '''igt-tutorial'''/Slicer3-lib/CMake-build/bin
 +
 
 +
  $ cd OpenIGTLink-build
 +
  $ ccmake ../OpenIGTLink
 +
 
 +
If the previous command has completed without error, you can start building:
 +
  $ make
 +
 
 +
Upon completion, you should find '''libOpenIGTLink.so''' (Linux) or '''libOpenIGTLink.dylib''' (Mac OS X) at '''igt-tutorial'''/OpenIGTLink-build
 +
 
 +
Copy libOpenIGTLink.so (Linux) or libOpenIGTLink.dylib (Mac OS X) into '''igt-tutorial'''/Slicer3-build/lib/Slicer3/Modules/Debug

Latest revision as of 17:47, 16 October 2008

Home < IGT:ToolKit < Build-OpenIGTLink

Back to IGT:ToolKit

Notes before you begin

  • Slicer3 is assumed to have been built on your computer in the directory igt-tutorial. This means that you have the directories igt-tutorial/Slicer3, igt-tutorial/Slicer3-build and igt-tutorial/Slicer3-lib
  • CMake 2.6 is absolutely required. If you don't have it installed, you can use the version of ccmake found in igt-tutorial/Slicer3-lib/CMake-build/bin (it will be CMake 2.6)

Instructions

First, get the OpenIGTLink module source code from the repository: 

 $ cd igt-tutorial
 $ svn co http://svn.na-mic.org/NAMICSandBox/trunk/IGTLoadableModules/OpenIGTLink OpenIGTLink

Create a new build directory: 

 $ mkdir OpenIGTLink-build

Configure using CMake 2.6:

  • Run CMake - CMake is found in igt-tutorial/Slicer3-lib/CMake-build/bin
  • Set the source code directory to igt-tutorial/OpenIGTLink
  • Set the build directory to igt-tutorial/OpenIGTLink-build
  • Press the 'c' key (or the configure button) - this give you a dialog box telling you that you haven't set the Slicer build directory yet
  • Set Slicer3_DIR to your build directory of Slicer3 (i.e. Slicer3-build)
  • Press 'c' (or the configure button) again
  • Then press the 'g' key (or the OK button) to generate the Visual Studio solution (Windows) or makefiles (linux)

Windows

  • Open OpenIGTLink.sln in the OpenIGTLink-build folder
  • Build -> Build Solution

Upon completion, you will find OpenIGTLink.dll in OpenIGTLink-build/Debug

Copy OpenIGTLink.dll into igt-tutorial/Slicer3-build/lib/Slicer3/Modules/Debug

Linux / Mac OS X

  • ccmake is found in igt-tutorial/Slicer3-lib/CMake-build/bin
 $ cd OpenIGTLink-build
 $ ccmake ../OpenIGTLink

If the previous command has completed without error, you can start building: 

 $ make

Upon completion, you should find libOpenIGTLink.so (Linux) or libOpenIGTLink.dylib (Mac OS X) at igt-tutorial/OpenIGTLink-build

Copy libOpenIGTLink.so (Linux) or libOpenIGTLink.dylib (Mac OS X) into igt-tutorial/Slicer3-build/lib/Slicer3/Modules/Debug

Retrieved from "https://www.na-mic.org/w/index.php?title=IGT:ToolKit/Build-OpenIGTLink&oldid=31090"