Difference between revisions of "IGT:ToolKit/Build-OpenIGTLink"
From NAMIC Wiki
| Line 2: | Line 2: | ||
===Notes before you begin=== | ===Notes before you begin=== | ||
| − | * Slicer3 is assumed to have been built on your computer in the directory '''igt-tutorial'''. This means that you have the directories igt-tutorial/Slicer3, igt-tutorial/Slicer3-build and igt-tutorial/Slicer3-lib | + | * Slicer3 is assumed to have been built on your computer in the directory '''igt-tutorial'''. This means that you have the directories igt-tutorial/Slicer3, igt-tutorial/Slicer3-build and '''igt-tutorial'''/Slicer3-lib |
| − | * CMake 2.6 is absolutely required. If you don't have it installed, you can use the version of ccmake found in igt-tutorial/Slicer3-lib/CMake-build/bin (it will be CMake 2.6) | + | * CMake 2.6 is absolutely required. If you don't have it installed, you can use the version of ccmake found in '''igt-tutorial'''/Slicer3-lib/CMake-build/bin (it will be CMake 2.6) |
===Instructions=== | ===Instructions=== | ||
First, get the OpenIGTLink module source code from the repository: | First, get the OpenIGTLink module source code from the repository: | ||
| − | $ cd igt-tutorial | + | $ cd '''igt-tutorial''' |
$ svn co http://svn.na-mic.org/NAMICSandBox/trunk/IGTLoadableModules/OpenIGTLink OpenIGTLink | $ svn co http://svn.na-mic.org/NAMICSandBox/trunk/IGTLoadableModules/OpenIGTLink OpenIGTLink | ||
| Line 15: | Line 15: | ||
Configure using CMake 2.6: | Configure using CMake 2.6: | ||
| − | * Run CMake - CMake is found in igt-tutorial/Slicer3-lib/CMake-build/bin | + | * Run CMake - CMake is found in '''igt-tutorial'''/Slicer3-lib/CMake-build/bin |
| − | * Set the source code directory to igt-tutorial/OpenIGTLink | + | * Set the source code directory to '''igt-tutorial'''/OpenIGTLink |
| − | * Set the build directory to igt-tutorial/OpenIGTLink-build | + | * Set the build directory to '''igt-tutorial'''/OpenIGTLink-build |
* Press the 'c' key (or the configure button) - this give you a dialog box telling you that you haven't set the Slicer build directory yet | * Press the 'c' key (or the configure button) - this give you a dialog box telling you that you haven't set the Slicer build directory yet | ||
* Set '''Slicer3_DIR''' to your build directory of Slicer3 (i.e. Slicer3-build) | * Set '''Slicer3_DIR''' to your build directory of Slicer3 (i.e. Slicer3-build) | ||
| Line 30: | Line 30: | ||
''' Linux / Mac OS X ''' | ''' Linux / Mac OS X ''' | ||
| − | * ccmake is found in igt-tutorial/Slicer3-lib/CMake-build/bin | + | * ccmake is found in '''igt-tutorial'''/Slicer3-lib/CMake-build/bin |
$ cd OpenIGTLink-build | $ cd OpenIGTLink-build | ||
| Line 38: | Line 38: | ||
$ make | $ make | ||
| − | Upon completion, you should find '''libOpenIGTLink.so''' (Linux) or '''libOpenIGTLink.dylib''' (Mac OS X) at igt-tutorial/OpenIGTLink-build | + | Upon completion, you should find '''libOpenIGTLink.so''' (Linux) or '''libOpenIGTLink.dylib''' (Mac OS X) at '''igt-tutorial'''/OpenIGTLink-build |
Revision as of 17:40, 16 October 2008
Home < IGT:ToolKit < Build-OpenIGTLinkBack to IGT:ToolKit
Notes before you begin
- Slicer3 is assumed to have been built on your computer in the directory igt-tutorial. This means that you have the directories igt-tutorial/Slicer3, igt-tutorial/Slicer3-build and igt-tutorial/Slicer3-lib
- CMake 2.6 is absolutely required. If you don't have it installed, you can use the version of ccmake found in igt-tutorial/Slicer3-lib/CMake-build/bin (it will be CMake 2.6)
Instructions
First, get the OpenIGTLink module source code from the repository:
$ cd igt-tutorial $ svn co http://svn.na-mic.org/NAMICSandBox/trunk/IGTLoadableModules/OpenIGTLink OpenIGTLink
Create a new build directory:
$ mkdir OpenIGTLink-build
Configure using CMake 2.6:
- Run CMake - CMake is found in igt-tutorial/Slicer3-lib/CMake-build/bin
- Set the source code directory to igt-tutorial/OpenIGTLink
- Set the build directory to igt-tutorial/OpenIGTLink-build
- Press the 'c' key (or the configure button) - this give you a dialog box telling you that you haven't set the Slicer build directory yet
- Set Slicer3_DIR to your build directory of Slicer3 (i.e. Slicer3-build)
- Press 'c' (or the configure button) again
- Then press the 'g' key (or the OK button) to generate the Visual Studio solution (Windows) or makefiles (linux)
Windows
- Open OpenIGTLink.sln in the OpenIGTLink-build folder
- Build -> Build Solution
Upon completion, you will find OpenIGTLink.dll in OpenIGTLink-build/Debug
Linux / Mac OS X
- ccmake is found in igt-tutorial/Slicer3-lib/CMake-build/bin
$ cd OpenIGTLink-build $ ccmake ../OpenIGTLink
If the previous command has completed without error, you can start building:
$ make
Upon completion, you should find libOpenIGTLink.so (Linux) or libOpenIGTLink.dylib (Mac OS X) at igt-tutorial/OpenIGTLink-build
